 |
|
Elcometer
142 ISO 8502-3 Dust Tape Test Kit
The Elcometer
142 ISO 8502-3 Dust Tape Test kit allows assessment of the quantity
and size of dust particles on surfaces prepared for painting. Dust
on blast cleaned surfaces can reduce coating adhesion, leading to
premature coating failure and sub-standard coating finish. The
kit can be used in accordance with the recommendations of BS EN
ISO 8502-3 either as a pass/fail test or as a permanent record of
the presence of dust.
|
 |
|
Elcometer
130 SCM400 Salt Contamination Meter
This very easy
to use salt contamination meter measures the level of salts on the
surface. Soluble salts on a surface are absorbed into a special
filter paper soaked with distilled water. The Elcometer 130 measures
the conductivity of the wet paper, calculates the salt level and
displays it in ug/cm˛.
|
 |
|
Elcometer
135A Bresle Sampler
Supplied with
the Elcometer
138/2 Surface Contamination Kit, the Elcometer 135A is a
self-adhesive rubber film patch with a sealed compartment used for
taking samples of soluble impurities on a test surface.
|
 |
|
Elcometer
135B Bresle Patch
Supplied with
the Elcometer
138 Bresle Salt Kit, the Elcometer 135B is a self-adhesive
rubber film patch with a sealed compartment used for taking samples
of soluble impurities on a test surface.
|
 |
|
Elcometer
138/2 Surface Contamination Kit
Measuring the
level of contaminants on a surface prior to application of the coating
is essential to ensure the quality of the coating and that its optimum
lifetime is achieved. If the coating is applied to a contaminated
surface, which is not properly prepared, it could fail prematurely
resulting in costly re-coating and high maintenance costs.
|
 |
|
Elcometer
138 Bresle Kit & Elcometer 135 Bresle Patches
Well known
in the protective coatings field, the Bresle Patch is one of the
most popular tests for soluable salts. A patch is adhered to the
substrate and the soluable salts are dissolved into distilled water
using a rinsing motion caused by a syringe. A conductivity meter
is then used to calculate the slat level.
|
 |
|
Elcometer
134 CSN – Chlorides, Sulphates & Nitrates
Designed to
accurately measure surface chloride, sulphate and nitrate ions in
minutes, the Elcometer 134 ‘CSN Salts’ offers the user the ability
of trouble-free testing in the field. Supplied in an ABS plastic
carrying case for easy portability around the site, each field kit
is supplied with full instructions attached to the inside lid.
|
 |
|
Elcometer
134A Chloride Ion Test Kit for Abrasives
Chlorides deposited
on a surface by contaminated abrasive during blasting can cause
a coating to fail prematurely. Contamination can build up, particularly
if the blast media is recycled several times. The Elcometer 134A
is an easy to use, accurate field test which determines if your
abrasive is contaminated with chlorides and thus prevent costly
surface-related failures.
|
 |
|
Elcometer
134S Chloride Detection Kit for Blast Cleaned Surfaces
Chloride salts
left on the surface before the first coat is applied can result
in the coating system being forced off the surface by corrosion
or blistering before the full life of the coating has been reached.
Salts are extracted using a rubber tube and the level of chloride
on the surface is identified using a simple glass tube which identifies
the concentration level.
|
 |
|
Elcometer
134W Chloride Ion Test Kit for Water/Liquids
Coatings can
fail due to chlorides being deposited on a surface by contaminated
water during pressure washing, UHP water jetting or wet abrasive
blasting. The Elcometer 134W is an easy to use, accurate, field
based test which determines if your wash water is contaminated with
chlorides and thus prevent costly surface coating failures.
|
 |
|
Elcometer
128 Pictorial Surface Standards
Elcometer’s
range of Surface Standards, covers most of those required for surface
cleanliness. They include: The swedish standard, the british standard
and the sspc standards vis 1 and vis 3.
|
